Hook up amp to rear speakers, yahoo answers

Will i benefit by having an amp for my door speakers Polk Audio

Wayne, When replacing speakers and wiring, after disconnecting the factory wiring from the speaker, you can leave it installed as it was. Hi Todd, You seem to have sorted it out. Run speaker wires from your speakers to your amp's installation location.

How to hook up an amp to car speakers

Which is the best car stereo available in market? Previous Next Sort by votes. The resistor does take some power, but in a domestic install this is normally quite okay.

So just wondering if I can leave the harness speaker connections alone if I do that. Eventually I moved back to Charlottesville, Virginia and opened a small demo recording studio. Keith Parker from Bastrop La. All Audio Calculators Electrical Calculators. Justin, chatting and If your receiver checks out okay you should check all the wiring and the amplifier.

  1. Figure out where you want your amp, how you'll get power to it, and what if any components will be installed near it.
  2. At some point in the future I ant to ad a sub in the trunk.
  3. They actually pay me to ramble on, rant, and explain the things I love about music, electronics, and getting good sound.
  4. Be sure to secure the speaker boxes to your vehicle.
  5. Okay, so after running front and rear speaker outputs from the head unit to amp's speaker input terminals, what do I do about the amp's sub input since I have no outputs from the head unit?
  6. Related Questions Car speaker hook up without an amp?

The volume controls on the other two speakers will only reduce the volume, not make them louder than the four speakers. How to wire Four Speakers to One Amplifier. This article was written by the It Still Works team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information. If you bought your gear from Crutchfield, you can call Tech Support for free help troubleshooting your system. Make sure all cables are secured and not installed in a way that will distress them.

Buck Pomerantz

Don't hook it up, cut it or do anything else with it! Buck, your patience is admiral. Cant i just connect speakers to humax freesat box? But I may be misunderstanding.

  • Or would this damage the receiver or speakers?
  • Randy, According to Crutchfield's database, replacing the factory receiver means losing the navigation and satellite radio features of your vehicle.
  • Be sure the fuse holder is mounted in a safe place, and the power wires are all secured away from any moving parts.
  • They are known as being in parallel because, well, they are wired in parallel.
How to Wire Door Speakers to an Amp
Report Abuse

How can we help you today? If you need to turn each speaker on or off individually or have separate volume controls, you may need a speaker selector switch. Aaron, If your amp doesn't have a source switch for its sub channel, you'll have to tap four more wires from the existing eight speaker wires you've tapped into. The receiver's speaker outputs should remain unconnected to any wiring.

Yahoo Answers

Run all of your speaker wires. Many people get confused when we talk about a stereo amplifier. For the rest of this article, when we talk about an amplifier, upscale dating service chicago we are talking about either the left or right amplifier only.

Connecting Your Car Speakers to an Amp Use Your Factory Wiring

Hook up rear inwall speakers directly to tv without receiver or amp

If I understand correctly, they need to be hooked up in series, correct? Hook up all of the wires at the amplifier! Be sure you have this piece of equipment and a fuse before you even attempt to hook your amp up to your vehicle's electrical system.

Should 2 speakers be connected in Series or Parallel

Question Home theater speakers. The thickness of the speaker wires going to your tweeters will have nothing to do with their volume and tone. The speaker wires from the new stereo aren't used. Then you will need something to tell the amplifier to turn on.

Quick Links

If you replaced the factory-installed speakers, single taken the installation manual should tell you the impedance. Ok so I'm trying to connect my iPad to my car speakers and sub. Their toll-free number will be on your invoice.

Do I have to ground an antenna if I mount it to a pole in the ground? That plugs into the car, which has all the wiring that connects to the speakers. Just trying to clarify for myself, been out of the audio game for a while, and looking to do a completely custom install. Is there such thing as an adapter I can adapt to the adapter that goes into the factory amp and use for my new amp? But the radio doesn't have enough power to drive a sub.

Which speakers would you recommend I amplify, the front or rear? You'd connect both left front and rear speakers to one bridged channel and the right front and rear speakers to the other. Now I just installed a gm and ran new speaker wires to the four original speakers I connected the rca inputs to front and rear accordingly. If I connect an amplifier to my aftermarket door speakers, can I still use the speaker outputs from the back of the radio for more smaller speakers.

How to Connect 2 Speakers to 1 Amplifier - Geoff the Grey Geek
How to Connect 2 Speakers to 1 Amplifier
It Still Works

The only way you can tell if your amps can be strapped together and how to wire them is by referring to their instruction manual. Also be aware that the impedance volume controls will only reduce the volume from whatever the amp volume control is set to. Is that ok to by that amp? David, Not knowing exactly what subwoofers you have make it impossible to give advice on how to wire them together. You say you also have the harness that goes with your vehicle the one that plugs into the factory radio harness.

If you double click on a diagram you should see a slightly larger version for easier viewing. Do I need an amplifier or subwoofer? Strip the other ends and attach to the amp terminals. Two sub input rca on the amplifier. Jordan, Hopefully you meant to say you'll run the speaker wires from the harness to the amplifier's speaker outputs, not inputs - but it sounds like you're on the right track.

Jeff, You should never connect the outputs of two amplifiers together - in your case a receiver's amplified output and an amplifier - one will burn out the other, or both. Understanding Speaker Impedance. David, Check out How to connect an amp to a factory stereo for help with what you want to do. In any places where they'll need protection, radio carbon dating debunked be sure to cover them with a tough material.

Find what fits your vehicle. Their toll-free number is on your invoice. Source - factory unit connected to scosche hi low converter. Hook up a fuse holder near the battery.

Connect 2 Speakers in Parallel

  • Online dating cultural impact
  • How to tell someone you wanna hook up with them
  • Nigerian navy dating site
  • How does fut 13 matchmaking work
  • How radiometric dating works
  • Dating sites australia melbourne
  • Japanese dating rules
  • Ugly dating site photos
  • Dating advice for couples
  • How to tell if your ex is dating someone new